- 6,400 W, 2 x 2,400 W + 2 x 800 W an 4 Ω
- 4 channel DSP amplifier with dual-technology
- 2 power supplys, DSP-boards and Class-D module
- Integrated loudspeaker management systems (DSP) with audiophile sound quality
- 2 x 120 preset locations, including 2 different presets assignable simultaneously
- Software control via Dante (Digital Audio Network Through Ethernet)
- Intelligent wide-range switching power supplies with automatic worldwide voltage adjustment
- Dust protected by modular upside-down board assembly
- Very quiet, temperature controlled low-noise EBM Papst fan
- Tough, road-ready, stable and yet light aluminum housing
HDSP-0.4DDA
Quantity channel
4 CH, class-D latest generation
Power output 4 Ω
3,200 W (4 x 800 W)
Power output 8 Ω
1,800 W (4 x 450 W)
Power output 16 Ω
800 W (4 x 200 W)
Damping factor
> 1000 / 8 Ω, 1 kHz
Frequency responce
20 - 20,000 Hz
THD+N
< 0.05 % (20 - 20,000 Hz with 8 Ω)
Signal-to-noise ratio
> 118 dB (20 - 20,000 Hz with 8 Ω)
Voltage
Intelligent PFC wide-range power supply with soft start and automatic voltage selection:
85 - 135 V = 110 / 115 / 120 V Betrieb, 190 - 265 V = 220 / 230 / 240 V Betrieb, 50/60 Hz
Powerconnector
1 x 16 A powerCON TRUE1 INSignal connection digital
2 x Dante (Digital Audio Network Through Ethernet)
2 x Digital AES/EBU, AES67
Signal connection analog
4 x XLR female/male
Speaker Connections
4 x Speakon
Cooling
2 x temperature-controlled EBM-Papst low noise axial fan, air flow front to back
Protection
Input limiter, peak limiter
Start-up current limiting (soft start)
Protection circuit on and off transients
Under and over-voltage protection
DC-protection of outputs
Temperature monitoring of the heatsink and transistors
Realtime software-monitoring
Loudspeaker impedance measuring from each output channel (line-control)
Temperature measuring from each ampmodule
Real time meterbridge on PC per channel
Real time access for configuration on each channel
Speaker group building for access multiple speakers with one command
DSP sampling
64 bit, 96 kHz sample rate
DSP preset memory quantity
2 x 120 preset locations, including 2 different presets assignable simultaneously
Latency
0 - max. 500 microsecond
Dynamic range input
120 dB
Nominal input level
+ 6 dBu
Maximum input level
+ 23 dBu
Limiter
Two per way, in each input and output
Filter
10 parametric filter each in- and output, use as Bell, Shelving, Notch, or Allpass filter
Long delay section
0 - 800 ms (max. 275 m delay) in each input
Short delay section
0 up to 17 ms (max. 6 m delay) per output for time alignment between the acoustic centers
Phase adjustment
0 - 180°
X-Over
Butterworth, Bessel, Linkwitz-Riley Filter
Software
Bi-directional realtime VA-WLAN-remote network, software for PC and MAC
Manual hand operation
with 4 x button and 2 x digital encoder-wheel in the internal menu navigation, function lockable
Display
2 x LED display
2 x LCD display with software dimmable and switchableBody housing
19"/2 HE, 450 mm deep, strong black colored aluminum housing
Weight
5.2 kgThe HDSP-0.4DDA is a 4-channel DSP amplifier with dual technology and has an output power of 3.200 W into 4 Ω.
DDA stands for a new generation of DSP and input boards that can process a variety of signals: DANTE, Digital AES/EBU, AES67 and analog inputs. The signals can be looped further.
The Voice-Acoustic HDSP amplifier series has been developed with the most demanding requirements in audio quality and reliability in mind. With the high number of output channels, for the first time, it has become possible to separately filter bi and tri amping with the HDSP series cost effectively. The intelligent wide-range switching power supply automatically detects the AC input values making it possible to use anywhere in the world.
The integrated loudspeaker management systems (DSP – digital signaling processor) work with a 64 bit/96 kHz sampling rate in audiophile sound quality. Premium converters offer a 120 db dynamic range and can process an input level of up to + 23 dBu. This amplifier series is specked out with the factory settings for the speakers, limiter and time alignment for the output channels. Additionally each input channel boasts 10 parametric filters (Bell, High Shelf, Low Shelf, Notch, Allpass), compressors, flexible routing, phase settings, a lengthy delay section for delays up to 275 meters, and an input limiter. The series is also equipped with enough memory to add your own presets for the use of loudspeakers from other manufacturers. The amplifiers are likewise available without Voice-Acoustic factory presets.
The LCD display on the front side enables all functions to be manually accessed from a digital rotary encoder and buttons. Our Voice-Acoustic’s VA-WLAN remote software for PC, Mac or App offers even more convenient access to these controls. This software makes it possible to link, remotely operate and monitor up to 128 individual HDSP amplifier units or self-powered loudspeakers in one common network. Linking is accomplished fully automatically via IP-address. The connection operates bi-directionally in real-time and provides a diverse scope of system feedback (headroom, temperature, and impedance measurement).
One major advantage of Voice-Acoustic power amplifiers is their modular capability. Multiples of highly effective state-of-the-art Class-D modules are fitted with separate power supplies and separate DSP boards to endure redundancy and guarantee supreme operational safety. This easy-to-service modular style allows for simple and fast exchange of components by any electrical assistant in a short time. Compared to conventional multi-channel power amplifiers, which have to be powered with one power supply, the HDSP amplifier’s modular capabilities guarantee maximum performance and lots of headroom – even in a deep base range without simultaneously influencing other channels.
The electronics have been mounted upside-down in the super sturdy 19" aluminum housing. Any dust particles will float to the floor of the box and not lay down on the platinum. All 2HE power amplifiers have identical housing and back cover plates.